Why Put The Starter Switch Key In Your Pocket During A Pre Trip Inspection? You should keep the starter switch key in your pocket while you perform the pre-trip inspection because.
While you are performing the pre-trip inspection, you do not want someone (such as a co-driver) who is unaware of your location to start your vehicle and accidentally injure you.
?
? 25.
What is the best way to check the sides and rear of your vehicle? Regularly looking out the window and checking behind you. Checking your mirrors regularly and more often in special situations. Installing a rear camera system is the safest way to see sides of your vehicle.
Why Put The Starter Switch Key In Your Pocket During A Pre Trip Inspection? – Related Questions
?
The Pre-Trip Inspection is a verbal test.
Say at least 2 things about every item you inspect.
Point to, or touch, every item that you inspect.
Mention all damaged items to the tester.
How can you start moving without rolling backward?
If stopped on a hill, how can you start moving without rolling back
When you do a walk around inspection you should?
Step 5: Do Walkaround Inspection
What are five things you should check for on the front of your truck during a walk around inspection?
Name some things you should check on the front of your vehicle during the walk-around inspection.
Your most important objective is to select and maintain a speed that is not too fast for the following:
Total weight of the vehicle and cargo.
Length of the grade.
Steepness of the grade.
Road Conditions.
Weather.
What 3 kinds of emergency equipment must you have?
What three kinds of emergency equipment must you have
?
The most important reason to perform a pre-trip inspection is for your safety.
It can be dangerous to go out on the road with a load that is not secured, brakes that are damaged, wiring that is not connected, etc.
What should you do if you can’t see 15 seconds ahead of you?
In order to avoid last minute moves, you should look down the road 10 to 15 seconds ahead of your vehicle. A driver needs to look that far ahead to see hazards early. Constantly staring at the road just in front of your car is dangerous.
Which of these lights Cannot be checked at the same time?
Which of these lights cannot be checked at the same time
?
Next step for the pre-trip inspection is to check the side of the trailer and the tandems.
Wall – Make sure the wall is not damaged.
Lights – Lights should be on and flashing.
Tires – Tires should be properly inflated and have decent tread.
Hub seal – Make sure it’s not leaking and wiped with oil if transparent.
Which gear is best for driving uphill?
Make sure your wheels are properly aligned with our wheel alignment service. Uphill: Approach uphill situations with an appropriate amount of momentum, a higher gear (3rd in an automatic transmission) and less throttle to reduce torque, which also reduces wheel spin.
Can you roll backwards in Drive?
Automatic transmissions are built to give you smooth, consistent power to the wheels without feeling the abrupt acceleration or shifting of gears. This doesn’t mean you can “floor it” in reverse and slam the car into drive… this shock certainly WILL cause damage!
What should you do when you see a hazard in the road in front of you?
Switch on your hazard lights, check the traffic, and gently steer your car to a safe area as far off the road as possible, braking gently when you’re ready to stop. Once you’re out of harm’s way, get out of the car, survey the situation, and phone for help.
When backing up which side should you back towards?
Backing toward the right side is very dangerous because you cannot see as well.
If you back and turn toward the driver’s side, you can watch the rear of your vehicle by looking out the side window.
Use driver-side backing-even if it means going around the block to put your vehicle in this position.
How do you recognize a distracted driver?
4 ways to identify a distracted driver
Drifting away from center. Due to lane markings, it is pretty easy to see if a car near you is swerving.
Sudden braking. Another sign of a distracted driver is sudden braking.
Lingering at intersections.
The driver is wearing headphones.
?
It ensures the safety of not just the driver, but also everyone else on the road.
Currently, there are no guidelines as to how long a pre-trip inspection should take.
If you check everything you should be checking, a full inspection should take you approximately 30 to 50 minutes.
What do DOT officers look for?
The DOT official will inspect the driver’s documents including license, medical certificates, logs, HOS documentation, inspection reports, and Hazmat endorsements. The driver will also be checked to make sure they aren’t under the influence of any drugs, alcohol, or any other hazardous material.
What thing should you check during a trip?
2. What things should you check during a trip
