What Should Fuel Rail Pressure Be On Duramax?

What Should Fuel Rail Pressure Be On Duramax?

What Should Fuel Rail Pressure Be On Duramax? The Duramax diesel fuel system needs the same super pressures that all diesels need in order to properly inject the fuel. Note that the fuel rail pressure is at 24,053 psi.

How much fuel rail pressure does a Duramax have? Note that the fuel rail pressure is at 24,053 psi. As stated previously, the fuel pressure with the Ignition relay unplugged needs to be a minimum of 2500 to 3500 psi during cranking for the return rate test results to be valid.

What should the fuel rail pressure be? A minimum rail pressure of 5,000 PSI (345 bar) is required to start the engine. 2. The rail pressure during normal idle should be 5,600 – 6,500 PSI (386 – 448 bar).

What should lb7 fuel rail pressure be at idle? At 185 it should be about 4.3kpsi. It might go up or down 100 psi, that’s normal.

What Should Fuel Rail Pressure Be On Duramax? – Related Questions

What causes low fuel rail Duramax?

The common cause is a foreign object gets down the filler neck of the fuel tank. The most common thing we see is the paper seals of diesel fuel additive. This is not a fun job but is not too difficult. Run the fuel level down as much as possible, then the tank will have to be dropped.

What causes low fuel rail pressure?

Error Code P0087 is defined as Fuel Rail/System Pressure Too Low. Typical causes for low fuel pressure include a dirty fuel filter, weak pump, incorrect tank venting, restricted fuel lines, a clogged pump inlet strainer and faulty electrical control.

What happens if fuel pressure is too high?

Too high of pressure may result in, over fueling of the engine. As a result, this can lead to a rough running engine; poor fuel mileage, and black smoke coming from the exhaust. If your regulator is going bad, your car could display several different symptoms.

What causes high fuel rail pressure?

As we discussed, high fuel pressure means that the air to fuel ratio is off-kilter. The causes for this imbalance of fuel pressure typically include either a bad fuel regulator or a clogged return line.

What happens if the fuel rail pressure sensor goes bad?

A faulty rail sensor may upset the air fuel ratio and cause the vehicle to experience performance issues such as a decrease in power, acceleration, and fuel efficiency, and in some cases may even experience stalling.

How much fuel pressure does a 6.6 Duramax have?

Use common sense safety practices when servicing any diesel system: While maximum control oil pressure on a Power Stroke can reach nearly 4,000 psi, the Duramax fuel system is pressure-relieved at a blistering 27,550 psi.

What should LB7 injector balance rates be?

When viewing the rates, a cylinder with (+) means that its injector is using more fuel than the average fuel rate and a (-) translates to less fuel. GM states that balance rates should be no more than plus or minus 4 (+4/-4) in park at operating temperature.

Where is the fuel pressure relief valve on a Duramax?

This valve often referred to as FPRV is located in the rear of the driver’s side fuel rail on the LLY, LBZ, and LMM, and is buried in the valley on the LB7 and functions much like the Temp and Pressure valve on your water heater.

Where is the fuel rail pressure sensor located on a 6.6 Duramax?

The sensor is mounted on the right fuel rail under the EGR Cooler. Using conventional wrenches and sockets, a tech needs to remove the EGR cooler and heat shield(s) to gain access to the sensor.

Does a Duramax have a fuel pump in the tank?

The GMC and Chevy Duramax pick-up trucks do NOT have a lift pump to supply fuel to the engine. From the factory, the CP3 injection pump is the truck’s only means of getting fuel from the tank to the engine.

How do you diagnose a bad CP3 pump?

To see if the smoke disappears while idle, you can test cutting out a cylinder when using a scan tool. Check for a dirty air filter, and clean or replace it if needed. A high-pitched squeal beneath the load may be heard if there is boost leaks or exhaust leaks.

How do you fix fuel rail system pressure too low?

What repairs can fix the P0087 code

Why is LBZ so good?

The LBZ employed a thicker block casting, meatier connecting rods, and a higher pressure common-rail fuel system. This gave it more power and reliability versus any other Duramax to that point.

How does a fuel rail pressure relief valve work?

The pressure regulation valve serves with the quantity control valve to control the common rail pressure. The pressure relief valve simply allows more or less high pressure fuel to flow into the back leak system thus increasing or decreasing the fuel pressure in the rail. Excess fuel returns to the fuel tank.

Will a clogged fuel filter cause low fuel pressure?

A clogged fuel filter causes low fuel pressure that results in a lean fuel condition and engine misfire. This can result in poor fuel mileage, rough idling and possibly cause the check engine light to come on. Once that light is on, it’s time for a trip to the repair shop.

Can you drive with low fuel pressure?

If you put too little fuel then your engine will run lean which is probably ok, but it will run hotter. This may damage your valves or pistons, requiring an engine rebuild. But yes the engine will probably run and feel ok. Sure as long as you still have good fuel pressure.

How do you fix high fuel pressure?

Start the engine; the fuel pressure should remain the same. Snap the throttle and make sure it increases; this an indication of a good fuel pump. Test a vacuum-operated fuel pressure regulator by removing the vacuum line while monitoring fuel pressure. The pressure should increase (5-15 psi.).

Frank Slide - Outdoor Blog
Logo
Enable registration in settings - general