What can you use as a substitute for bar and chain oil?
What can I substitute for bar and chain oil? Chainsaw Bar And Chain Oil Alternatives
Motor oil. If you find yourself in a situation where you need to use your chainsaw but you don’t have any of the correct oil, one of the obvious options is motor oil.
Vegetable oil.
Canola oil.
Drained hydraulic fluid.
What can I use in place of bar oil? Tips for replacing chain oil with vegetable oil:
Use canola oil – Canola oil is currently the most common environmentally compatible chain-and-bar lubricant.
Vegetable oil is thinner – Vegetable oils have lower viscosities than the bar/chain lubricants and therefore flow more readily.
More items•
Can I use regular oil for bar and chain oil? No one recommends using old recycled motor oil. Remember that used motor oil drained from a vehicle has microscopic metal bits that act as an abrasive, which is not good for the chain or bar. Some note that used motor oil could burn up your bar and chain sooner, which will make up for any cost savings.
What can you use as a substitute for bar and chain oil? – Related Questions
What happens to a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Can I use gear oil as chain lube?
It’s perfectly fine to use gear oil for lubing motorcycle’s chain, I’m myself using it for years. Use 90 grade gear oil if you lube every 500–700km while the thicker 140 grade oil lasts for 800–1000 km. Also, there’s no need to clean the chain every 500km.
What kind of oil do you use for a chainsaw chain?
Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant. Vegetable-based oils are triglycerides or natural esters that come from agricultural crops.
What weight is chain and bar oil?
For this reason, bar and chain oil should suit most loggers. They usually have a 10W relative weight during winter and 30W during warm weather conditions. You can check most oils authenticity by putting on the chainsaw and looking for any oil spills at about 8 inches on the other side.
Is bar and chain oil the same as 2 cycle oil?
Always use 2 stroke oil only for the mix. Oil is “relatively” cheap, compared to small engines. Bar oil needs to be sticky in the summer for lubrication and to flow with “stickyness” for bar and chain lube in the cold.
Can I use 5w30 for chainsaw bar?
It will work, just wear the bar and chain faster. I don’t belive it will gum anything up.
Can I use 10w30 for bar oil?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden!
What is SAE 30 oil?
SAE 30 oil is a motor oil that has been given a viscosity rating of 30 by the Society of Automotive Engineers, according to AA1Car Automotive Diagnostic Help Center. Motor oils typically have ratings from 0 to 50.
Can I use chainsaw without bar oil?
Running a chainsaw without bar oil will cause mechanical problems, and some serious safety issues, such as: Kickback. Chain breaking. Dulls the chain.
Does cutting wet wood dull a chainsaw?
Does Cutting Wet Wood Dull a Chainsaw
How often should you add bar oil to chainsaw?
How often should I lubricate the sprocket in the tip of my bar
Can I use WD40 on bike chain?
Spray the WD-40 Bike Degreaser onto the surface of your bike chain and give it adequate time to work. On top of that, the WD-40 Bike Degreaser can be used for the cleaning and degreasing of other moving parts as well.
What is the best gear oil?
Best Sellers in Gear Oils
#1. Quicksilver 802851Q02 High Performance SAE 90 Gear Lube.
#2. Valvoline High Performance SAE 80W-90 Gear Oil 1 GA.
#3. Lucas Oil 14.5 Ounce 10301 Heavy Duty Grease, 14.5 oz,Green.
#4. Valvoline SynPower SAE 75W-140 Full Synthetic Gear Oil 1 GA.
#5.
#6.
#7.
#8.
More items
Is Chain Wax better than lube?
If you want to use your motorcycle immediately you lubricate the chain, then you’ll be better off using chain lube. If you ride your bike in dirty and dusty terrains, then you should consider using a chain wax since it has proven to pretty effective at keeping off elements such as dirt, grime, water, etc.
What is the difference between bar and chain oil and motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Can I use 2 cycle oil as chain oil?
One final note: This article recommends using vegetable oil to replace chain oil in chainsaws. However, this does NOT mean replacing “mix” oil which is used for the gas mix. For mix oil, you must use the petroleum-based 2-stroke mix oil recommended by the chain saw manufacturer.
Can you use motor oil in place of 2 stroke oil?
Yes, you can. Use it in the same proportions you would use 2 stroke oil. The main point being to maintain the lubricating qualities of the oil added to the fuel, too little can cause bearing and bore damage. Its a fairly light grade, (lighter than engine oil) burns quite well & is cheap!
