How do you attach a ledger board?
How do I attach flashing to ledger board? How to Flash a Deck Ledger Board
Proper flashing to a house frame.
Cut the flashing with tin snips.
Score with a utility knife.
Bend flashing with a block and framing square for a 90 degree bend to fit inside the house corner wall.
Measure carefully to cut around the door.
Cut flashing.
Slip flashing under siding.
What size should a deck ledger board be? As a general rule, you should use the same size of board for the ledger as you plan to use for the joists. You can use a larger board, however, if it allows for a better connection to the house framing. Calculate the length as 3 inches less than the width of the deck framing.
Should I use ledger board spacers? If you have your ledger tight against the rim joist it’s much stronger. If it’s flashed properly you won’t have to worry about spacers.” Flashing, of course, is key. Any water trapped behind the ledger can induce rot, if not in the ledger itself than in sheathing and framing of the house.
How do you attach a ledger board? – Related Questions
How much weight can a ledger board hold?
The ledger is 10′ long so every foot of ledger must be designed to carry at least 200 lbs of load.
Can a ledger board be two pieces?
You are required to have a minimum of two of those assemblies on your ledger, and your inspector could well consider a two-piece ledger as actually being two ledgers.
How do I attach rafters to ledger?
Attaching Rafters to a Ledger
What are Ledger locks used for?
Ledgerlok screw is the first wooden screw, specially designed to attach a deck ledger board to the rim stud of a house and not to mention, it requires no pre-drilling like normal lag screws.
This structural screw is easy to install, as it is coated with a three-step coating process which prevents corrosion.
What is the ledger board?
1 : a horizontal board forming the top rail of a simple fence or the handrail of a balustrade. 2 : a flooring board in scaffolding.
How far can a 2×6 joist span without support?
2-grade 2×6 joists can span up to 10 feet 9 inches from beam to beam when spaced the standard 16 inches apart with a maximum live load of 30 inches per square foot.
In comparison, No.
-1 grade lumber can span slightly further to 10 feet 11 inches under the same parameters.
Should I use 4×4 or 6×6 deck posts?
While there may be a handful of circumstances that only require the minimum 4×4 deck post, you will more than likely want to choose a 6×6 post for the deck. It provides more stability for larger decks, the ability to hold a heavier load, and more room for notching.
Can you build a deck without a ledger board?
A freestanding deck is a self-supporting deck structure built independently from a house wall ledger board attachment.
Some freestanding decks stand alone in an open area.
Above-ground pool decks are often built freestanding in this fashion.
What does the ledger board attach to?
The deck ledger is the deck floor rim board attached to the house, and it should be positively connected to the floor structure of the main building with bolts or lag screws, not nails.
How far apart should lag bolts be on a ledger board?
The bolts or lags must be placed along the ledger in two rows—one row along the top and one along the bottom—with the fasteners staggered between the two rows at the spacing indicated by the IRC table. For example, on a deck with a joist span of 15 feet, the lag screws are spaced 11 inches apart.
How much weight can a 2 by 10 hold?
1,200 lbs.
Each 2×10 will support 1,200 lbs.
Can I attach a ledger board to wall studs?
Mike Guertin (on Instagram @mike_guertin), a builder and remodeler in East Greenwich, R.
I.
, and a presenter at JLC Live, responds: Yes, it’s technically possible to fasten a deck ledger to the narrow faces of 2-by studs rather than to a solid rim joist.
How much weight can a 2×8 joist hold?
A live load of 60 pounds per square foot demands more support and shorter spans. Spaced at 12 inches, the joist may only span 16 feet 8 inches. At 16 inch spacing, 15 feet 2 inches and 13 feet 3 inches at 24 inch spacing.
Can you put ledger board over siding?
In order to install the ledger board, you usually need to remove the house’s siding. Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection. Set the blade depth so you won’t cut into the house sheathing below the siding.
Should a ledger board be pressure treated?
Installing the Ledger Board
Can a ledger board be 2×8?
A 2×8 up to 12 feet; 2×10 to 15 feet and 2×12 to 18 feet. The larger the deck, the larger the joists. In typical deck construction, with a ledger on one side of the joist and beam on the other, the size of the joists is driven by the size of the deck and based on the general maximum spans mentioned above.
Can I use a 2×4 for a ledger board?
When you have to use a ledger, use at least a 2×4, and use lag screws with washers or through-bolts.
While your example is interior, the problem with ledgers is even worse on exposed decks.
