How Do You Adjust A Craftsman Chainsaw?
How do you adjust the carburetor on a Craftsman 42cc chainsaw? With the engine running turn the high speed needle clockwise until the engine runs rough. Turn the needle counter clockwise slowly until the engine runs smooth. Make this adjustment with both screws and the engine should run smoothly and at the highest fuel efficiency.
How do you adjust a high and low carburetor? Locate the two fuel-adjustment screws on the side of the carburetor. One will be labeled “Hi” and the other “Lo.” The “Hi” screw regulates the engine at full throttle and the “Lo” regulates the fuel when the engine is idling.
Why does my chainsaw bogs down at full throttle? The reason for that may be you’re using the saw at altitude or the carburetor adjustment has simply slipped. The saw also won’t operate well at speed if the air filter or spark arrestor or carburetor are dirty.
How Do You Adjust A Craftsman Chainsaw? – Related Questions
Why does my chainsaw dies when I give it gas?
Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.
Why does my chainsaw start and then stop?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
How do you adjust a chainsaw carburetor?
How to Tune a Chainsaw Carburetor
Start your saw and run it for a few minutes to warm it up.
Set your saw down, let it idle for 30 seconds, and then pick it up and tip it forward (handle up and bar down).
If it keeps running, go to Step 4.
Rev (accelerate) the idling saw.
If it accelerates fine, go to Step 6.
•
How do you tell if a carburetor is rich or lean?
If the insulator near the plug tip is a nice light tan colour then it’s running approximately correct at that load/rpm. If they’re white then it’s running lean, if they’re a dark brown or worse colour then it’s running rich.
How do you adjust a craftsman carburetor?
How to Adjust a Carburetor in a Craftsman
Locate the carburetor on your Craftsman equipment.
Turn the main mixture and idle mixture screws on the carburetor counterclockwise about one full turn with a flat-head screwdriver.
Start the engine with the transmission in neutral and let it run for several minutes.
How do you change the carburetor on a Craftsman chainsaw?
Instructions
Drain the fuel tank.
Remove the cylinder shield.
Disconnect the spark plug wire and remove the air filter.
Remove the carburetor mounting nuts.
Detach the air filter housing.
Disconnect the fuel lines.
Remove the carburetor.
Install the new carburetor.
What is the spark plug gap on a Craftsman chainsaw?
(0.63 mm).
Why does my Craftsman chainsaw bog down?
Fuel Flow to the Carburetor
Should you run a chainsaw at full throttle?
Chainsaws come with a chain break to prevent any injury that may occur from a kickback. To prevent a kickback while working, you should: Apply full throttle before cutting. Avoid using the top of the chainsaw.
Why does my 2 cycle engine stall when I give it gas?
Fuel and Air Filters
What do the high and low screws do on a chainsaw?
Most Pro Saw Engines Have Three Carburetor Adjusting Screws:
How do you fix a chainsaw that won’t stay running?
Vent in the Fuel Cap is plugged – If the vents in the fuel caps are clogged the fuel becomes vacuum locked. Check the cap and clean it or replace. High-Low adjustments screws may need calibrating – If you have these screws in your chainsaw, adjust them by turning both screws clockwise until you reach the end – gently.
Why does my chainsaw keeps stalling out?
An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw is stalling when you pull the throttle trigger or it doesn’t reach its full power, adjust the high-speed (H) screw.
What causes chainsaw to backfire?
What you are getting is after fire, usually caused by unburned fuel reaching a hot muffler. A backfire is back through the carb, a whole ‘nuther problem related to timing issues. Exactly. Commonly referred to as “misfire”.
What happens when you run straight gas in a chainsaw?
If you’ve put straight gas in the fuel tank, don’t start the engine. If straight gas is used, it can damage and ruin the piston and crankcase within a minute, as the gas doesn’t take long to burn out these sensitive parts. Drain the tank immediately into a separate fuel container.
What does the L and H mean on a chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
How do you adjust a carburetor?
Here’s How To Adjust a Carburetor
Remove the Engine Air Filter. The air cleaner and filter assembly must be removed for you to access the carburetor.
Locate Adjustment Screws.
(Optional): Hook up Vacuum Gauge.
(Optional): Set Baseline.
Warm the Engine Up.
(Optional): Adjust Idle Speed Screw.
Adjust the Air-Fuel Mixture.
