How Do I Change The Throttle Cable On My Motorcycle?
When should I change my motorcycle throttle cable? For my motorcycle, the throttle and clutch cables are replaced due to any of the following reasons:
Frayed.
Age of more than 2 years. Bike is parked outside without cover for most part of the year.
Damage to the adjuster nuts.
Kinked.
Chaffing of outer rubber/coating.
Throttling or clutching is taking an effort.
How do I install a throttle cable? Push the new cable through the firewall and into the engine compartment. Step 2: Hook the new cable up to the accelerator pedal. Slide the new cable through the slotted hole in the accelerator pedal. Step 3: Reconnect the throttle cable to the retaining bracket.
Why do some motorcycles have two throttle cables? A push/pull throttle cable is an upgrade to the old standard single throttle cable linkage. The second cable pulls the carb closed so it isn’t stuck wide open. On a road race bike at 165mph+ approaching a tight turn with little run off area, riders want that peace of mind that if they close the gas, it will close.
How Do I Change The Throttle Cable On My Motorcycle? – Related Questions
How long do motorcycle throttle cables last?
That being said it should be replaced every 2 to 3 years to prevent being stuck on the side of the road with a snapped cable when all the dealers are closed and you can’t get a cable.
Do you need to lube new throttle cables?
If throttle action feels gritty
Are throttle cables universal?
In today’s modern vehicles, throttle cables are obsolete with the widespread use of drive-by-wire throttle pedal assemblies. Our universal throttle cable offerings fit most any application or engine type and mounting location.
How do you reattach a throttle cable?
Push the new cable through the firewall and into the engine compartment. Step 2: Hook the new cable up to the accelerator pedal. Slide the new cable through the slotted hole in the accelerator pedal. Step 3: Reconnect the throttle cable to the retaining bracket.
Is throttle cable and accelerator cable the same?
Your car’s accelerator cable, also known as a throttle cable, is a braided metal wire that connects the gas pedal to the engine throttle plate.
How tight should throttle cable be?
Most motorcycle manufacturers recommend about 2 to 3 millimeters of throttle free play, but over time the cables will stretch and settle into their housings and you’ll end up with more slack.
How much does it cost to replace a throttle cable?
A throttle cable replacement usually costs around $50 to $100. To ensure that you’re getting the right fit, enter your vehicle’s year, make, and model in our built-in search function.
How do I adjust throttle free play?
Most factory manuals will tell you that 2–3mm is the correct amount of throttle free play. The adjuster actually changes the length of the cable’s exterior sleeve to alter the free play. Once you’ve determined if the free play needs adjustment, loosen the cable’s locking nut(s) near the throttle grip.
Can I use wd40 to lube throttle cable?
WD 40 is a great quick and dirty solution to sticky cables. It flows great and flushes out that damn cable lube that gums up and attracts dirt. Use it regularly to keep moisture and dirt out.
How often do you replace throttle cables?
every three years
Over time cables can wear, get dirty or snagged. It is recommended that you change cables like your clutch and throttle cables every three years or every 10,000 miles.
Why is my throttle sticking on my motorcycle?
A sticky throttle could be caused by worn cables, lack of lubrication in the cables or the cable getting bound up somewhere in the mechanism. Or it can be caused by an issue with the carburetor or EFI. If the screws in the throttle housing are too tight it could cause the cable to stick.
How does Throttle work on motorcycle?
As you pull the throttle, you open the valve, allowing more air+fuel mixture to enter in the engine and this increases the power. For bikes using electronic fuel injection, the throttle twist sends the position value to Engine Control Unit and the control unit opens the valve and injects fuel to the engine.
How long do throttle cables last?
How long you can expect your accelerator cable to last will depend in large measure on how often you drive. The more use the accelerator cable gets, the more prone it is to wear and tear. Usually, you can expect to get five years from your accelerator cable before it needs to be replaced.
Should you lube a new clutch cable?
Running Nekkid said: No you dont. The cables are teflon coated inside and oil can break that down.
Can you use chain lube on cables?
For cables, you shouldn’t use lube at all since it attracts dirt. However if you must, a dry wax based lube like White Lightning will attract the least amount of dirt. For chains you should use a lubricant that can actually continuously lubricate moving parts.
What kind of cable is throttle cable?
Throttle Cables
What happens if throttle cable breaks?
When the gas pedal is pressed, the cable is pulled and opens the throttle. If the cable breaks, or comes out of adjustment far enough, it can affect the drivability of the vehicle to the point where the car will not be drivable until the problem is addressed.
